Water Filtration and Softening System Installers
844-529-7473 | Crest Park CA
The piping around a water softener can be confusing when attempting to install a water softener. A cold water branch before the water softener doesn’t necessarily indicate a problem. It’s standard procedure to branch off one cold water line to supply outdoor hose connections (and sometimes another to the kitchen sink and refrigerator icemaker if you don’t want to drink softened water).
Water for gardens and lawns doesn’t need to be softened. The main supply line to the rest of the house continues to the softener. Once the water leaves the softener, it should branch into two lines: a cold line that runs to interior fixtures and faucets, and a line that feeds the water heater. The outgoing line from the water heater then runs to interior fixtures and faucets that dispense hot water. In addition to those lines, there should be a soft water bypass loop with a valve you can open to bypass the softener if you need to disconnect it temporarily without disturbing the water supply to the house.
Simply put, drains were designed to drain water – and water isn’t always the only thing going down. Granted, there’s not always much you can do to avoid this. There are certain things you can do proactively to lessen the chance of a clog. Before we explore those options though, let’s take a look at three types of drains and some common reasons why they clog.
Kitchen Sink Drains
Kitchen sinks put up with a lot of abuse. Think about it… they endure grease, food products, paper products, and just about everything in between. It’s not hard to imagine why all of that stuff might lead to a clog every once in a while, especially if your sink drain has a smaller diameter than average drain pipe.
Bathroom Sink Drains
Bathroom sinks don’t have to deal with as many types of debris, but they do have to deal with an entirely different mess: human hair. Human hair has this nasty habit of clinging to everything it comes in contact with, including inside sink drains. Length is almost irrelevant. Long or short, your drain will clog if there’s enough hair.
Bathroom Tub Drains
Bathroom tubs have to deal with a lot of hair as well. They are also susceptible to many different kinds of bar soaps. Believe it or not, a tiny chunk of bar soap can last quite a while in a drain, especially if it starts building up. Between hair and soap, which are akin to brick and mortar, tub drains can clog easily if you aren’t careful.
These are some of the most common reasons your drain might get clogged. Other reasons include accidently dropping a foreign object into the drain (jewelry, contact lens case, cell phone, etc.). In other cases, the clog might be caused by the shape, length, and diameter of the pipes themselves. The more sharp turns and bends there are, and the smaller diameter the pipe is, the likelier you will experience consistent clogging issues.
Stopping and fixing a leaky pipe, while two very different processes, can prevent damage to your home, your time, and your wallet by temporarily or permanently resolving the problem at hand.
Stopping the Leak (The Temporary Solution)
Upon discovering a leak, stopping the leak should be your first priority whether the plumbing project necessary to fix it is big or small. Stopping a leak with the following steps prevents further water damage, the waste of more money, and makes replacing the pipe in the future a much simpler process.
Fixing the Leak (The Permanent Solution)
While stopping a leak with the steps above is a great temporary fix for small leaks, time sensitive projects, and inexperienced individuals, it does not guarantee a permanent fix to your water leakage problem. This is due to the fact that usually when one leak is fixed, other leaks will spring up in other places because the whole section of pipe needs replaced due to corrosion. Because of this, we first recommend that you immediately contact a professional plumber after temporarily stopping a leak.
One of the most common–and most upsetting–plumbing problems you can have in your home is when something goes wrong with your toilet. Whether that’s your toilet overflowing, running continually or leaks around the seal at the base of your fixture, toilet repairs are not something that you can postpone.
Common toilet repair issues
- Toilet continues to run. When your toilet continues to run, it’s likely that your float, refill tube and/or ballcock need to be replaced.
- There is water pooling around the base of your toilet. Water collecting on the floor at the base of your toilet usually means that the seal is wearing out and needs to be replaced.
- Phantom flushes. Phantom flushes, when the toilet flushes seemingly by itself at random intervals, is usually a sign that there’s a slow leak between the tank and the toilet bowl.
- The water is slow to fill the bowl. A toilet bowl that is slow to refill is a sign that there is debris clogging the plumbing leading to the toilet bowl.
- The toilet is clogged. Serious clogs require an industrial-size auger to push the debris that’s clogging the pipe down into the larger sewer pipe.
Fixing your toilet quickly and reliably requires the skill and training of a professional plumber. However, that doesn’t mean that you have to spend a fortune or have your house torn up for an extended period of time. To learn more about affordable, easy toilet repair solutions, call Plumbers today.
Basically, when something is obstructing the flow of water inside your drainpipe, it causes the water to drain slower than usual. This creates air bubbles inside the main drain and that’s the gurgle you hear.
What causes a partial clog?
There are a number of things that cause a blockage inside your plumbing system: hair, dirt, food, and soap particles are a few of many.
If you suspect the clog is minor and you know what you’re doing, you could try removing the clog using a plunger the right way. If a good plunge does the trick, nice job!
If this does not fix the problem, you probably have a heavy clog that requires the knowledge and tools of a trusted plumbing professional.
Important warning: Do NOT pour commercial drain cleaners down your drain—these chemicals contain toxic fumes and can seriously damage your pipes. Plus they usually only remove enough of the clog to get your drain running—and then clog again later.
Water Filtration System Installation Crest Park California
Water Softener System Installation
Carbon Based Self Regenerating Water Filter System
Good Quality Water Filtration and Softener System Installation
It doesn’t matter whether your home’s water supply originates from a nicely or perhaps your municipal system you need to be sure that the water is protected for the family. Contaminated water could cause various health diseases like diarrhea, vomiting, typhoid, cholera, and many others. You may prevent your family from contracting these diseases by installing a water purification and softener system. We have been here to install these systems as your representative to make certain that your household uses neat and contaminant-free water. Here are some more benefits that will make you aware about why installing a water softener and water purification system is essential.
•Safe h2o – Come up with a smart move by purchasing a water filtration system to protect yourself from spending on health conditions due to polluted water. You will do yourself and your loved ones a world of favor by preventing contaminated water from entering your house.
•Reduce plumbing issues – Heavy metals, chemicals, and minerals in water may cause your plumbing system to corrode with time. Installing a water softener can fix this concern. It keeps your hot-hot water heaters, water pipes, along with other home appliances safe.
•Prevent skin irritation – The inclusion of chemicals and heavy metals may cause skin irritation among those with sensitive skin. You could possibly see rashes and allergies frequently. A lot of people can also have problems with skin problems like psoriasis and eczema. A water purification system can alleviate these complaints as you will now use chemical and pollutant-free water.
Installing a water purification system
We utilize the latest tools in the business to install your water filtration system. In addition to installation, we also recommend the very best filtering system in accordance with your financial budget.
Here’s what our water filtration installation process looks like:
1. Draining the system and cutting the pipe
We start with shutting off your home’s main water supply. One of our experts will open the lowest faucet in the home to drain the majority of the water from the pipes. Next, you need to tell us where you need to install the filtering method. We make a couple of cuts around the marked part of the pipe. Then, we twist the handle to tighten the cutter and make certain the cutter cuts all the way through. Next, we work with a reamer blade to get rid of burrs through the pipe’s inside.
2. Attaching fittings and positioning the filter
We take advantage of the small end of your compression nut on sides from the cut pipe. Our technician threads the brass fitting in the filter housing and positions the filter based on the manufacturer’s recommendations. We use Teflon tape to seal the ends of the filter port and fitting. Then, we snugly tighten the fittings and view the filter’s position between the two ferrules.
3. Test running the filter
We open your home’s water supply and look just how the filter works. Using it for the hour helps to know whether the filter captures chemical toxins and pollutants or perhaps not.
Installing a water softener system
We use two water softener installation systems, dependant upon the space you can afford
•A typical basement installation involves creating the softener right beside your home’s central water purification system. We usually try to keep the liquid softener nearby the main shutoff valve as it helps make the system better.
•Besides basement installation, we provide slab foundation installation for your personal water softener system. We start with turning from the main water supply before draining water lines. A technician measures and checks the connections towards the water softener.
•Next, we fill half the brine tank with salt then shut the bypass channel. We turn your water supply line to check on for leaks.
•We start the softener if we don’t find any leak.
Our experienced technicians are prepared for water softeners and filtration systems from various brands. Phone us today to put together a scheduled appointment so that we can install these systems within your house as soon as possible.